The discone antenna or discone aerial is often used where an omnidirectional wide band or bandwidth RF antenna design is needed.
The discone antenna is used for many radio communication applications from radio scanning and monitoring for the commercial or military services to the home scanner enthusiasts.
In view of their size, weight and windage or wind resistance, these antennas are normally used for frequencies above 30 MHz, but on occasions they can be designed for lower frequency usage although the space required can be large.
Discone antenna basics
ag捕鱼王程序揭秘Although sometimes called a scanner antenna, the discone antenna receives its name from its shape: it consists of a top disc underneath which is a cone.
ag捕鱼王程序揭秘The disc and cone can be made from solid metal sheet, but this would increase the windage, i.e. wind resistance or wind loading and its weight. Normally they are made from rods that are able to electrically simulate the disc and the cone. Often between six and sixteen rods are used, with most designs being within the lower region of the number of rods.
ag捕鱼王程序揭秘The discone antenna can operate over frequency ranges of up to 10:1 dependent upon the particular design, and it also offers a relatively low angle of radiation (and reception). This makes it ideal for VHF / UHF applications as its greatest sensitivity is parallel or almost parallel to the Earth. However towards the top of its frequency range it is found that the angle of radiation increases slightly.
ag捕鱼王程序揭秘Although it is widely used for receiving applications, the discone antenna is less commonly used for transmitting. There are several reasons for this. Although it offers a wide bandwidth, it is not optimised for a particular band of frequencies and is less efficient than many other types of RF antenna design that can be used.
Additionally the wideband nature of the RF antenna means that spurious signals can be radiated more easily and the level of reflected power will vary over the operating range and may rise above acceptable limits in some areas. However with modern equipment, the filtering of the signal is normally very good, and this should not be too much of an issue.
Physical aspects of the discone
The basic RF discone antenna or scanner antenna design consists of three main components: the insulator, the cone elements and the disc elements.
ag捕鱼王程序揭秘Of the RF antenna components the insulator size governs a number of factors of the performance of the antenna. It is made from insulating material and acts to hold the disc and cone elements in place, keeping them a fixed distance apart. In fact this distance is one of the factors that determines the overall frequency range of the particular RF antenna design. It is represented by the distance D on the diagram.
Secondly, the cone elements should be a quarter wavelength at the minimum operating frequency. This can be calculated from the formula:
A is the length of the cone elements in millimetres.
ag捕鱼王程序揭秘 f is the frequency in MHz
Thirdly the disc elements should be made to have an overall length of 0.7 of a quarter wavelength. This can be calculated from the formula:
B is the length of the disc elements in millimetres.
f is the frequency in MHz
ag捕鱼王程序揭秘 The diameter of the top of the cone is mainly dependent upon the diameter of the coaxial cable being used. This determines the upper frequency limit of the antenna. The smaller the diameter the higher the frequency. It is represented by the distance C on the diagram.
ag捕鱼王程序揭秘For many designs operating in the VHF / UHF region of the radio spectrum it is around 15 millimetres. The spacing between the cone and the disc should be about a quarter of the inner diameter of the cone, i.e. around three of four millimetres.
Additional vertical element on discone
Often discones will be seen with an additional vertical element attached to the top of the antenna. This is often the case when they are used as a scanner antenna.
ag捕鱼王程序揭秘This additional vertical element on the discone helps to extend the lower frequency response for the overall antenna, giving improved performance at lower frequencies.
The downside to the addition of the vertical element is that it can reduce the efficiency at higher frequencies.
The way in which the discone operates is relatively complicated, but it can be envisaged in a simplified manner. The disc and cone elements sufficiently simulate an electrically complete disc and cone from which the energy is radiated. As a result the greater the number of elements, the better the simulation, although in reality there is a balance between performance, cost and wind resistance. Often around six elements are used, but the number is not critical.
ag捕鱼王程序揭秘In operation energy from the feeder meets the RF antenna and spreads over the surface of the cone from the apex towards the base until the vertical distance between the point on the cone and the disc is a quarter wavelength. In this way it is possible for the energy to be radiated or received efficiently.
ag捕鱼王程序揭秘The RF antenna radiates and receives energy that is vertically polarised, and the radiation pattern is omnidirectional in the horizontal plane. The antenna radiates most of the energy at a low angle which it maintains over the most of the operating range. Typically there is little change over a range of 5:1 and above this a slight increase in the angle.
With the feed point at the top of the RF antenna the current maximum point is also at the top. It is also found that below the minimum frequency the antenna presents a very bad mismatch to the feeder. However once the frequency rises above this point then a reasonable match to 50 ohm coax is maintained over virtually the whole of the band.
In terms of its operation requirements, the antenna is self contained. Unlike various vertical antennas it does not require the use of any ground connection, etc. Also the discone is an unbalanced antenna and can be fed directly from a coaxial feeder.
The discone antenna is widely used at VHF and above where a wide band antenna is needed. Although not directive in the same way that a Yagi is directive, it provides a low angle of radiation that is ideal for terrestrial applications both for commercial and amateur / hobby radio communications applications.
More Antenna & Propagation Topics:
EM waves Radio propagation Ionospheric propagation Ground wave Meteor scatter Tropospheric propagation Cubical quad Dipole Discone Ferrite rod Log periodic antenna Parabolic reflector antenna Vertical antennas Yagi Antenna grounding Coax cable Waveguide VSWR MIMO
Return to Antennas & Propagation menu . . .